Ask us anything
Kenmore 665.13213K901, how to replace the thermal fuse?
Replacing the thermal fuse in a Kenmore 665.13213K901 dishwasher is a task that requires attention to safety and careful handling of electrical components. The thermal fuse helps protect the dishwasher from overheating. Here's a general guide to help you through the process: 1. Safety Precautions: Begin by ensuring the dishwasher is disconnected from the power source. Unplug it from the electrical outlet or turn off the circuit breaker. 2. Access the Fuse Area: The thermal fuse is typically located on or near the control board. Depending on the model, you may need to remove the front panel, control panel, or kickplate to access the fuse. Consult your user manual for specific instructions. 3. Disconnect the Wires: Before touching any wires, take pictures or label them to ensure proper reconnection. Gently disconnect the wires from the thermal fuse. 4. Remove the Old Fuse: The thermal fuse is often secured with mounting clips or screws. Remove any fasteners holding the fuse in place. Carefully slide out the old thermal fuse. 5. Prepare the New Fuse: Ensure you have the correct replacement thermal fuse that's compatible with your dishwasher model. 6. Install the New Fuse: Slide the new thermal fuse into the same position as the old one. Align it with the mounting holes. 7. Secure with Mounting Hardware: Use the screws or clips you removed earlier to secure the new thermal fuse in place. Make sure it's snug but not overly tightened. 8. Reconnect Wires: Attach the wires to the new thermal fuse according to your notes or photos. Ensure each wire is securely connected to the corresponding terminal. 9. Reassemble the Dishwasher: Reattach any panels or components you removed earlier. Make sure all panels are securely fastened. 10. Plug in and Test: Plug the dishwasher back in and run a short test cycle to ensure that the new thermal fuse is functioning properly. Monitor the cycle for any unusual behavior. 11. Check for Abnormalities: Keep an eye on the dishwasher during the test cycle to ensure that it's operating normally, and there are no signs of overheating. Always consult your dishwasher's user manual for model-specific instructions and diagrams. If you're not comfortable with the repair process, consider seeking the assistance of a professional appliance technician.
Similar Questions
- What heating element do I need for a Whirlpool EE3J50RD045V hot water heater?
- How to fix a Frigidaire front load washer pauses itself before spin cycle?
- What should be done to keep the Allegiance 16 Central Air Conditioner running smoothly?
- Kenmore filter reset light AC, no filter reset button.
- I have two copper tubings that were hot and now it's cool on my Amana fridge, what does that mean?
- Is air duct cleaning necessary?
- What should be the care routine for the Lennox ML196E Gas Furnace to ensure its long-term efficiency?
- So I have a doctor's appointment until 12 PM. Do you think I can switch appointments? Can you do it between 12 and 4 PM?
- Does thermador cooktop have an on switch
- What should be checked if my HMCG2 16.5 SEER2 Modulating Side-Discharge Air Conditioner is not cooling effectively?
Similar Blog
October 12
7434
Home
Add Vintage and Antique Pieces into Your Home Decor
Vintage home decor gives your decor a sense of time and history, but you don't have to buy many antiques to achieve the appearance. The secret is incorporating ...
February 26
9111
Plumbing
Six Spring Plumbing Maintenance Tips
As the chill of winter fades away, it's time to prepare your home for the vibrant season of spring. Neglecting essential maintenance could lead to unwanted surp...
April 11
3922
Plumbing
The 5 Benefits Of A Sewer Camera Inspection
As a homeowner, it's easy to overlook the importance of maintaining your home's plumbing system, especially when it comes to your sewer lines. But the truth is ...
Couldn't find the right question?
You can send your question to our support team. We'll get back to you as soon as possible